Ok, so I am using the CC3300, and my difficulty is getting the data from MPR121 loop to feed into the Xively, I have broken up each of the sensors into Case instances, similar to the Bildr tutorial, I am posting the code below. (if that helps) much appreciated.

/*Copyright (c) 2010 bildr community

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ //

include <Adafruit_CC3000.h>

include <ccspi.h>

include <SPI.h>

include <string.h>

include "utility/debug.h"

include <stdlib.h>

include "mpr121.h"

include <Wire.h>

define ADAFRUIT_CC3000_IRQ 3

define ADAFRUIT_CC3000_VBAT 5

define ADAFRUIT_CC3000_CS 10

Adafruit_CC3000 cc3000 = Adafruit_CC3000(ADAFRUIT_CC3000_CS, ADAFRUIT_CC3000_IRQ, ADAFRUIT_CC3000_VBAT, SPI_CLOCK_DIV2);

define WLAN_SSID "" // cannot be longer than 32 characters!

define WLAN_PASS ""

// Security can be WLAN_SEC_UNSEC, WLAN_SEC_WEP, WLAN_SEC_WPA or WLAN_SEC_WPA2

define WLAN_SECURITY WLAN_SEC_WPA2

define WEBSITE "api.xively.com"

define API_key ""

define feedID ""

//Somewhere in here I need to create an instance to register the mpr121? //possibly could be in the wrong order //have not been able to get the mpr121 to register to the internet yet, I have tried a couple different formats //I have both the Imp April and CC3300 break out //

Serial.println(F("\nInitializing...")); if (!cc3000.begin()) { Serial.println(F("Couldn't begin()! Check your wiring?")); while(1); } int irqpin = 2; // Digital 2 boolean touchStates[12]; //to keep track of the previous touch states

void setup(){ pinMode(irqpin, INPUT); digitalWrite(irqpin, HIGH); //enable pullup resistor

Serial.begin(115200); Wire.begin();

mpr121_setup(); }

void loop(){ readTouchInputs(); }

void readTouchInputs(){ if(!checkInterrupt()){

//read the touch state from the MPR121
Wire.requestFrom(0x5A,2); 

byte LSB = Wire.read();
byte MSB = Wire.read();

uint16_t touched = ((MSB << 8) | LSB); //16bits that make up the touch states


for (int i=0; i < 12; i++){  // Check what electrodes were pressed
  if(touched & (1<<i)){

    if(touchStates[i] == 0){
      //pin i was just touched
      Serial.print("Pin ");
      Serial.print(i);
      Serial.println(" was just touched");

      switch (i) {
        case 0:
         // 0 was just touched
         Serial.print("");
         Serial.print("");
         break;
         case 1:
         // 1 was touched
         Serial.print("Did you Wash your Hands! GROSS"); 
         break;
         case 2:
         // 2 was touched
         Serial.print(""); 
         Serial.print("");
         break;
         case 3:
         // 3 was touched
         Serial.print(" ");
         Serial.print(" ");
         break; 
         case 4:
         // 4 was touched 
         Serial.print(" ");
         Serial.print(" ");
         break;
         case 5:
         // 5 was just touched
         Serial.print(" ");
         break;
         case 6: 
         // 6 was just touched
         Serial.print(" ");
         break;
         case 7:
         // 7 was just touched
         Serial.print(" ");
         break;
         case 8:
         // 8 was just touched
         Serial.print(" ");
         break;
         case 9:
         // 9 was pressed 
         Serial.print(" ");
         break;
         case 10:
         // 10 was just pressed 
         Serial.print(" ");
         break;
         case 11:
         // 11 was just touched
         Serial.print(" "); 


      }           

    }else if(touchStates[i] == 1){
      //pin i is still being touched
    }  

    touchStates[i] = 1;      
  }else{
    if(touchStates[i] == 1){
      Serial.print(" pin ");
      Serial.print(i);
      Serial.println(" Shelf is no longer being touched");

      //pin i is no longer being touched
   }

    touchStates[i] = 0;
  }

}

} }

void mpr121_setup(void){

set_register(0x5A, ELE_CFG, 0x00);

Looking at using the WiFly or something similar. Like the CC3300. Either way I am stuck on register a touch being pushed to Xively and shield picking up the touches, not the mpr121 yet the wifi module itself. If that clarifies. Thanks again….

Both actually. Looking over my previous reply that is a little confusing.