Shopping Cart 0 items
log in register
Today's Deals Forum Desktop Site
All Categories
Featured
Brands
Development
Sensors
Tools
Miscellaneous
Components
E-Textiles
Robotics
Wireless & IoT
Audio

Creative Commons images are CC BY 2.0

Favorited Favorite 3
Wish List

Nordic nRF52840 BLE Module (MDBT50Q-1MV2)

$ 8.50

Stock availability

Added to your shopping cart

Raytac’s MDBT50Q is a BT 5.2 stack (Bluetooth® low energy or BLE) module designed based on Nordic nRF52840 SoC solution, which incorporates: GPIO, SPI, UART, I2C, I2S, PMD, PWM, ADC, NFC and USB interfaces for connecting peripherals and sensors.

It features an embedded 2.4GHz transceiver supports Bluetooth 5.2, IEEE 802.15.4 (Thread & Zigbee) & 2.4Ghz RF & ANT+ upon customer’s preference. Compact size with (L) 15.5 x (W) 10.5 x (H) 2.05 or 2 mm. Low power requirements, ultra-low peak, average and idle mode power consumption. Fully coverage of BLE software stack. BLE & RF transmission switching helps products fit all operation system and most hardware

  • Bluetooth 5, IEEE 802.15.4, 2.4 GHz transceiver
    • -95dBm sensitivity in 1Mbps Bluetooth low energy (BLE) mode
    • -103dBm sensitivity in 125Kbps BLE mode (long range)
    • +8 dBm TX power (down to -20 dBm in 4 dB steps)
    • On-air compatible with nRF52, nRF51, nRF24L and nRF24AP Series
    • Programmable output power from +8dBm to -20dB
    • RSSI (1dB resolution)
    • Supported data rates:
    • Bluetooth 5: 2 Mbps, 1 Mbps, 500 kbps, 125 kbps
    • IEEE 802.15.4-2006: 250 kbps
    • Proprietary 2.4 GHz: 2 Mbps, 1 Mbps
  • ARM Cortex –M4 32-bit processor with FPU, 64 MHz
  • Memory: 1MB flash / 256KB RAM
  • HW accelerated security
    • ARM TrustZone Cryptocell 310 security subsystem
    • 128 bit AES / ECB / CCM / AAR co-processor (on-the-fly packet encryption)
  • Advanced on-chip interfaces
    • USB 2.0 full speed (12Mbps) controller
    • QSPI 32MHz interface
    • High speed 32MHz SPI
    • Type 2 near field communication (NFC-A) tag with wake-on field
    • Programmable peripheral interconnect (PPI)
    • 48 general purpose I/O pins
    • EasyDMA automated data transfer between memory and peripherals.
  • 12 bit, 200ksps ADC – 8 configurable channels with programmable gain
  • 4 x 4 channel pulse width modulator (PWM) units with EasyDMA
  • Audio peripherals : I2S, digital microphone interface (PDM)
  • 5 X 32-bit timers with counter mode
  • Up to 4 x SPI masters / 3 x SPI slaves with EasyDMA
  • Up to 2 x I2C compatible 2-wire masters / slaves
  • 2 x UART(CTS/RTS) with EasyDMA
  • Quadrature decoder (QDEC)
  • 3 x 24-bit real-time counters (RTC)

Tags

Nordic nRF52840 BLE Module (MDBT50Q-1MV2) Product Help and Resources

Core Skill: Soldering

This skill defines how difficult the soldering is on a particular product. It might be a couple simple solder joints, or require special reflow tools.

4 Soldering

Skill Level: Experienced - You might be required to do some reflow or basic rework with SMD components. A heat gun, Heaterizer or other tools might be required, and a good understanding of SMD soldering as well as PTH soldering are required.
See all skill levels

Core Skill: Programming

If a board needs code or communicates somehow, you're going to need to know how to program or interface with it. The programming skill is all about communication and code.

3 Programming

Skill Level: Competent - The toolchain for programming is a bit more complex and will examples may not be explicitly provided for you. You will be required to have a fundamental knowledge of programming and be required to provide your own code. You may need to modify existing libraries or code to work with your specific hardware. Sensor and hardware interfaces will be SPI or I2C.
See all skill levels

Core Skill: Electrical Prototyping

If it requires power, you need to know how much, what all the pins do, and how to hook it up. You may need to reference datasheets, schematics, and know the ins and outs of electronics.

3 Electrical Prototyping

Skill Level: Competent - You will be required to reference a datasheet or schematic to know how to use a component. Your knowledge of a datasheet will only require basic features like power requirements, pinouts, or communications type. Also, you may need a power supply that?s greater than 12V or more than 1A worth of current.
See all skill levels

Comments

Looking for answers to technical questions?

We welcome your comments and suggestions below. However, if you are looking for solutions to technical questions please see our Technical Assistance page.

Customer Reviews

No reviews yet.