Shopping Cart 0 items
log in register
Today's Deals Forum Desktop Site
All Categories
Featured
Brands
Development
Sensors
Tools
Miscellaneous
Components
E-Textiles
Robotics
Wireless & IoT
Audio

33% off

Creative Commons images are CC BY 2.0

Favorited Favorite 9
Wish List

Environmental Sensor (Qwiic) - BME680

This board has gone red! Checkout the new version here - it incorporates a variety of small changes including a jumper to disable the power LED.

The BME680 from Bosch is a powerful sensor capable of sensing humidity, barometric pressure, temperature and indoor air quality. The BME680 can communicate over SPI or I2C (default). The SparkX carrier board provides jumpers to select between communication protocols (SPI or I2C) as well as the ability to change the I2C address and remove the I2C pull up resistors. The carrier board also incorporates two Qwiic connectors so you can start talking to the board immediately - no soldering required!

While the BME680 is a very small IC, getting actual indoor air quality (IAQ) out of the BME680 is difficult. If you need a more direct sensor we recommend the SparkFun Environmental Sensor Combo which uses the CCS811 along side the BME280. Both sensors have robust libraries and a direct calculation of tVOCs and equivalent CO2.

We currently do not have a library for the BME680 available but will be releasing one soon.

We do not plan to regularly produce SparkX products so get them while they’re hot!

NOTE: The I2C address of the BME680 is 0x77 and is jumper selectable to 0x76. A multiplexer/Mux is required to communicate to multiple BME680 sensors on a single bus. If you need to use more than one BME680 sensor consider using the Qwiic Mux Breakout.

Experimental Product: SparkX products are rapidly produced to bring you the most cutting edge technology as it becomes available. These products are tested but come with no guarantees. Live technical support is not available for SparkX products. Head on over to our forum for support or to ask a question.

Environmental Sensor (Qwiic) - BME680 Product Help and Resources

SparkFun Environmental Sensor Breakout - BME68x (Qwiic) Hookup Guide

May 14, 2020
A hookup guide to get started with the BME68x Environmental Sensor from Bosch. Monitor the air quality, temperature, humidity, and barometric pressure with this Qwiic sensor!
Favorited Favorite 1

Comments

Looking for answers to technical questions?

We welcome your comments and suggestions below. However, if you are looking for solutions to technical questions please see our Technical Assistance page.

  • Kiko Lobo / about 6 years ago / 2

    Q: Why does it state that: "While the BME680 is a very small IC, getting actual indoor air quality (IAQ) out of the BME680 is difficult."

    What does it mean it will be difficult? What does that mean and why?

  • Member #74687 / about 5 years ago / 1

    "We currently do not have a library for the BME680 available but will be releasing one soon." What is soon? Thanks and regards...

  • Member #1268791 / about 6 years ago / 1

    Continuing from last question I have changed how I have set up the Sensor which I am trying to communicate to via I2C. The 2 GND pins: Set to GND coming from Microprocessor(Nucleo-F446RE) The two 3.3 volts : Set to 3.3V wired from Microprocessor SDA : Wired directly to Microprocessor SDA Pin that has been set up (No pullup since there is one in breakout schematic) SCL: Wired directly to Microprocessor SCL Pin that has been set up (No pullup since there is one in breakout schematic) CS: No connect because in breakout it "defaults" to I2C SDI: No connect since not using SPI Interface SDO: No connect so Slave Adress should default to 0x77 I believe? SCK: No connect since not using SPI I based these connections off the breakout although I could have some thought wrong? I am looking at the SCL and SDA lines between the Microprocessor and Sensor and am seeing the SCL and SDA lines but on the 9th clock I am only seeing Nack. I have tried sending (0x77), (0x77<<1) to shift address in correct location, and tried (0x76)(0x76<<1) just to double check. Any thoughts or ideas?

  • Member #1268791 / about 6 years ago / 1

    Regarding this sensor the description here says that the sensor defaults to I2C but reading through the data sheet it says that to use I2C the CS pin must be connected to power. So my question is to use I2C is it default or will I need to connect it to power? Thanks

    • Oddstr13 / about 6 years ago / 1

      CS is pulled up to 3.3V with a 4.7k resistor by default. Cut trace in jumper SJ2 to disable this. (You still want a pull-up on that pin for SPI operation, however)

      See breakout schematics listed under documents.

Customer Reviews

4 out of 5

Based on 1 ratings:

Currently viewing all customer reviews.

Pretty complex device in a small package

by verified purchaser

Great sensor. Software is very difficult though. Bosch has released the software for this now, so you can use the actual sensors software. Seems to work pretty well. Sparkfun should update their tutorials for use with the new bosch software. It works pretty well.