Shopping Cart 0 items
log in register
Today's Deals Forum Desktop Site
All Categories
Featured
Brands
Development
Sensors
Tools
Miscellaneous
Components
E-Textiles
Robotics
Wireless & IoT
Audio

Creative Commons images are CC BY 2.0

Favorited Favorite 0
Wish List

AVR 20 Pin 20MHz 2K - ATtiny2313

Atmel's ATtiny2313 8-Bit Processor. 2K of program space and 15 I/O lines. UART compatible pins. Runs up to 20MHz with external crystal. Package can be programmed in circuit.

  • [D](http://cdn.sparkfun.com/datasheets/Components/General IC/doc2543s.pdf) [atasheet](http://cdn.sparkfun.com/datasheets/Components/General IC/doc2543s.pdf)

AVR 20 Pin 20MHz 2K - ATtiny2313 Product Help and Resources

Core Skill: Soldering

This skill defines how difficult the soldering is on a particular product. It might be a couple simple solder joints, or require special reflow tools.

2 Soldering

Skill Level: Rookie - The number of pins increases, and you will have to determine polarity of components and some of the components might be a bit trickier or close together. You might need solder wick or flux.
See all skill levels

Core Skill: Programming

If a board needs code or communicates somehow, you're going to need to know how to program or interface with it. The programming skill is all about communication and code.

2 Programming

Skill Level: Rookie - You will need a better fundamental understand of what code is, and how it works. You will be using beginner-level software and development tools like Arduino. You will be dealing directly with code, but numerous examples and libraries are available. Sensors or shields will communicate with serial or TTL.
See all skill levels

Core Skill: Electrical Prototyping

If it requires power, you need to know how much, what all the pins do, and how to hook it up. You may need to reference datasheets, schematics, and know the ins and outs of electronics.

2 Electrical Prototyping

Skill Level: Rookie - You may be required to know a bit more about the component, such as orientation, or how to hook it up, in addition to power requirements. You will need to understand polarized components.
See all skill levels

Comments

Looking for answers to technical questions?

We welcome your comments and suggestions below. However, if you are looking for solutions to technical questions please see our Technical Assistance page.

  • EvanAlmighty / about 10 years ago / 1

    Will you be carrying a 20 pin DIP socket soon?

  • Member #110998 / about 10 years ago / 1

    i'm longtime arduino user but i never breadboarded the attiny chips, this would be my first... i assume this should work fine but i'll ask a newb question...

    can i use the adafruit cc3000 wifi breakout module the same way that i would on a full arduino? is this mostly true for all arduino compatible components?

    thanks.

  • LordFawful / about 10 years ago / 1

    Does this have an Eagle part?

  • chrwei / about 11 years ago / 1

    the product card link no longer works.

  • markmoran / about 11 years ago / 1

    Any plans to sell the ATtiny261? Am In incorrect that the 261 is basically the "newer" version of the 2313, giving up the built-in serial for more ADC channels?

  • Member #219306 / about 12 years ago / 1

    Can anybody tell me the avrdude CMD line to write the fuse bits to put a 16 M Hz crystal on this MCU? This calculator only has up to 8 M Hz crystal http://www.engbedded.com/fusecalc/

    Something like this: avrdude -p usbtiny -c t2313 -U lfuse:w:0xce:m -U hfuse:w:0xdf:m -U efuse:w:0xff:m

    I did this and now the MCU is locked up.

  • Member #258816 / about 13 years ago / 1

    can we put an arduino bootloader in it?? like the uno bootloader???

    • ThinkerT / about 12 years ago / 1

      Sort of. Not the bootloader, but you can program it with Arduino. Here's a link. It's fairly easy! There's also stuff for ATTiny85's on that site.

  • disabelle / about 13 years ago / 1

    would this work with the msp-exp430 lunch pad? http://www.sparkfun.com/products/10020

  • ThinkerT / about 14 years ago / 1

    Could you load the Arduino bootloader on this?

    • fungus / about 12 years ago * / 2

      Yes...but it's much better to get yourself a $15 ISP programmer to use with these bare chips. Something like this: https://www.sparkfun.com/products/9825

      In the Arduino IDE the only difference you'll notice is you select an option from the "Tools->Programmer" menu instead of a COM port. You get more features than COM though, eg. You can set 'fuse' settings on the chips (to select clock sources, etc. (which you'll need to do with this chip unless you want it locked at 1mHz)

      You also don't lose a couple of K of flash memory to the bootloader - very important when you only have 2K of program space!

    • dcormier / about 13 years ago / 1

      Yes. See this thread.

      • ThinkerT / about 13 years ago / 1

        Okay. Thanks.<br />
        You can put it on ATTiny's: <br />
        http://hlt.media.mit.edu/wiki/pmwiki.php?n=Main.ArduinoATtiny4585

    • kdittyr / about 14 years ago / 1

      I don't believe you can... that would be the atmega168 and atmega328.

Customer Reviews

No reviews yet.