Creative Commons images are CC BY 2.0

Description: The SparkFun BlackBerry Trackballer Breakout gives you easy access to a trackball which measures up, down, left, and right movements, clicks on the board, as well as adding a bit of flair to your project with four built-in LEDs. The trackballer breakout can be hooked into an Arduino compatible device to provide you with an intuitive direction controller.

As you can see (and probably gather from the name), the BlackBerry trackball is the main feature of this board. Four tiny spindles on the trackball each have small magnets on their ends that each trigger a paired SMD hall effect sensor, giving the user the ability to track up, down, left, and right movement of the trackball. Underneath the trackball, there is a small SMD momentary switch. This allows the user to trigger events or make selections with a simple ‘click’. Also underneath the trackball are four LED which include white, red, green, and blue that can light up the clear trackball any color desired by the user. Combinations of the four LEDs lit up can also be used to customize the trackball color. In order to properly run the hall effect sensors, momentary switch, and LEDs, you will need to supply power on two headers broken out, labeled VCC and GND. Power supplied to the board should be regulated, but can vary anywhere from 2.5 - 5.25V.

The final feature of the trackballer breakout is the mounting PCB. The PCB, included to mechanically stabilize the trackball, is mounted to the breakout board using four Phillips 4-40 screws and four nylon 4-40 standoffs and is included to prevent the trackball from being ripped off of the breakout board. This mounting board can be replaced with other types of mechanical stabilization if you so choose. For example, if the trackballer breakout is mounted into a project enclosure, the top mounting PCB may be removed.

Note: Put your screwdriver away, the SparkFun Blackberry Trackballer Breakout comes fully assembled!


  • Translucent Select Button
  • 360° Direction
  • Hall effect sensors measure up/down/left/right movements of trackball
  • Red, blue, green, white LEDs to light up the trackball
  • Mounting PCB to mechanically stabilize the trackball
  • All pins broken out to 0.1" pitch header

Dimensions: 28.5mm x 24.8mm x 18mm (1.12" x 0.97" x 0.7")


Recommended Products

Customer Comments

  • This new breakout board (BOB) doesn’t list the Hall effect sensors used. Fortunately the previous version of the BOB included a link to the datasheet of the Hall effect sensor it used. Here’s a link to the Mouser part. Does anyone know if the new board uses the same sensor?

    • This board uses the same sensor (AN4884). The board was just redesigned for easier manufacturing and better durability in the field (less glue more screws).

Customer Reviews

5 out of 5

Based on 1 ratings:

Currently viewing all customer reviews.

1 of 2 found this helpful:

Awesome Customer Service!

I recently bought one of the ‘old’ “Sparkfun BB Breakouts”. I had done so, so that I could make a ‘mouse like device’ with the trackball. Needless to say, even though it worked, it required that you apply a bit of pressure before it would register movement very well, almost enough most of the time to push the button. So needless to say, the old version wasn’t going to work for the project it was intended for:O(

So the other day I saw this NEW Breakout. So I wrote customer service where I was answered promptly by “Ted”. Ted not only went through the trouble to setup and make sure that the specific problem I was having was fixed in the new revision. I then shamelessly asked for a discount for buy the new one, but Ted did way better than that, he then was able to arrange for Sparkfun to send me one of these free of charge! I was so exited I came right here to give this review. I plan to make a more in depth review of the breakout when it arrives, and I will post the link here. So thank you Sparkfun for being awesome, and having awesome people represent you.

~Bobby Leighton Imagn' Games

Related Tutorials

BlackBerry Trackballer Breakout Hookup Guide

March 26, 2015

A basic hookup guide for getting started with the SparkFun BlackBerry Trackballer Breakout Board.