Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
Sometimes referred to as "spade connectors," these quick disconnects are really useful as power connectors in prototyping or …
This is a handy cable for connecting a five pin GHR-05V type locking connector to breadboard friendly male pins.
This is the SMD version of [PRT-07948](http://www.sparkfun.com/products/7948), which is the unit we like to use as RTC backup…
This is a 1A Adjustable SOT-223 voltage regulator capable of outputting 1.2V to 18V. The LM1117 uses the same pin-out and set…
This is a SMD 6 pin right angle male header. We use this header on our [LilyPad Main Board](http://www.sparkfun.com/commerce/…
Huge 10mm through-hole LEDs.
Huge 10mm through-hole LEDs. Mood-light an entire wall!
This is a SMD 6 pin right angle female header. We realized that we have had the male version of this header available for awh…
This is a handy little device that can save your system from smoking. A resettable fuse (also known as a [PTC](http://en.wiki…
This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. Using two of these b…
These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work. T…
This is a USB 3.0 type A to Micro-B 9-pin cable.
This is a simple knob that connects to the extra large sized linear slide potentiometer.
TIMI-MB (mikroBUS™) is a 0.96” TFT LCD display module that is driven directly by a PIXXI-28 graphics processor from 4D La…
This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. **Note: **These are sold in single units. If you inten…
These are *very* bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictur…
These are simple 12-position screw terminals with 3.5mm pitch pins.
This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ r…
1.0M Ohm, 1/4th Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and perf boards.We've opted for a new and …
This 2x13 shrouded header has the same number and spacing of pins as the Raspberry Pi so you can easily connect via ribbon ca…
The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerom…
These Adam Tech Wall Adapter Cables are terminated with a standard European (CEE 7/7) plug at one end and three insulated spa…
This right-angle tactile switch has a great 'click' to it. Also, because it's a through-hole design it's very sturdy. Mount i…
This is a 40-pin surface mount FPC (Flat Printed Circuit) connector.
[RTC](http://en.wikipedia.org/wiki/Real-time_clock) stands for real time clock folks. The DS3234 is a low-cost, extremely acc…
This is a glass ferrule type fuse. It fits great with our 5mm fuse clips. The fuse is rated for 125VAC, up to 5A. Fuses are p…
The STA540 from STMicro is a 4-channel, [class AB](http://en.wikipedia.org/wiki/Electronic_amplifier#Class_B_and_AB) audio am…
Poke Home Connectors have been added on a number of our boards over the last few years by providing a simple terminal-type co…
These red and black jumper wires can be used for pretty much everything including breadboards, Arduinos, and any 0.1in pitch …
Huge 10mm through-hole LEDs. Mood light an entire wall!
A simple 10-pin cable.
The Elektor DIY LiPo Supercharger can charge a single-cell LiPo battery and protect it against the effects of overvoltage, ov…
The GD25Q40C (4M-bit) Serial flash supports the standard Serial Peripheral Interface (SPI), and supports the Dual/Quad SPI.
1/6th Watt, +/- 5% tolerance PTH resistor.
This is a small ambient light sensor that acts as an NPN transistor. The more the sensor is exposed to light, the stronger th…
The QC3.0 Power Supply Set (US) is a USB wall adapter with an input value of AC100-240V, and an output of 6V-6.5V/3A, 6.5V-9V…
ATtiny84A are low-power CMOS 8-bit microcontrollers based on the AVR enhanced RISC architecture.
PCB mount clip to hold a AA battery. Sold in single units, you'll need two. These work great for small, low power application…
This is the very popular RGB combo but in SMD form. These units have four pads with a common anode configuration. Use this on…
Nordic Semiconductor nRF24L01+. Transceiver chip operating in the 2.4GHz band. Take all the coolness of the nRF2401A and add …
The 'must have' IC for 3V projects. This is the RS232 converter IC that is capable of running at 3V and communicating with 3V…
These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won't work.
The ZMOD4450 Gas Sensor Module is designed for detecting gases associated with food ripening or rotting.
Ever wanted to see what's on that SIM card? Use these sockets in your next project to interface to any old SIM. 6-Pin standar…