Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE …
These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are cap…
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup…
This 10m (33') SMA extension does a great job of connecting your receiver or radio to a distant antenna with as little RF los…
The SparkFun 4-in-1 Multi-USB Cable is a four-headed cable that will ensure that you're never stuck looking for a USB cable t…
This is a time saving large kit of 700 jumper wires - cut, stripped, and pre-bent for your prototyping pleasure.
Magnet wire is super useful stuff, and when you need it there's nothing else that will work. Whether you're winding a transfo…
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. 5 pair…
This is a flexible silicone USB-C to USB-C power charging cable.
This is a SparkFun exclusive! These are 12" long, 26 AWG jumper wires terminated as male to male. Use these to jumper from an…
This 2x20 flat ribbon-cable fits the GPIO headers on the Raspberry Pi 3, 2, and B+ so you can easily connect to the low-level…
This is a USB to TTL Serial Cable which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this…
USB C is fantastic. But until we have converted all our hubs, chargers, and ports over to USB C this is the cable you're goin…
This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE c…
This panel mount USB micro-B extension cable enables you to more easily enclose a project that contains a USB micro-B port.
The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin. This is a pack …
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Cables…
This is a basic SMA male to female connector cable at 25cm in length and RG174 housing.
This panel mount USB-B (female) to micro-B (male) cable enables you to more easily enclose a project that contains a USB micr…
This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE…
This is an simple 3' long Micro-HDMI to HDMI cable. Nothing fancy, it just works!
This is a 4 pack of wires that are pre-terminated with an alligator clip on one end and a hookup pigtail on the other. Alliga…
These 0.8m cables have minor modifications that allow them to be be plugged into their ports regardless of orientation on the…
This is a SparkFun exclusive! These are 12" long, 26 AWG jumper wires terminated as female to female. Use these to jumper fro…
This is a SparkFun exclusive! These are 155mm long, 26 AWG jumpers with male connectors on both ends. Use these to jumper fro…
These are 101mm long 26AWG jumpers with male connectors on both ends. Use these to jumper from any female header on any board…
If you need to knock up a quick prototype there's nothing like having a pile of jumper wires to speed things up, and let's fa…
The Raspberry Pi Zero and Zero W are both equipped with a smaller CSI (Camera Serial Interface) port than on a full-sized Ras…
This is a handy cable for connecting a six pin GHR-06V type locking connector to breadboard friendly male pins.
This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST conn…
This is a SparkFun exclusive! These are 155mm long, 26 AWG jumper wires. Multiple jumpers can be installed next to one anothe…
This is a basic SMA male to female connector cable at 1M in length and RG174 housing.
The is the official, 1m, micro HDMI to HDMI Cable for use with the Raspberry Pi.
These 2m cables have minor, yet genius modifications that allow both ends (the A & Micro-B) to be plugged into their ports re…
This is a USB 2.0 type A to Micro-B 5-pin black cable. You know, the mini-B connector that usually comes with cell phones, Ca…
Jumper wires are awesome. Just a little bit of stranded core wire with a nice solid pin connector on either end. They have th…
This is a USB 2.0 type A to Mini-B 5-pin cable. You know, the mini-B connector that usually comes with USB Hubs, Cameras, MP3…
This is a USB to TTL Serial Cable which allows for a simple way to connect TTL interface devices to USB.
Three pin JST connector with red, black, and yellow colors. 5 inch wire outs. This cable comes fully assembled as shown and c…
TRRS connectors are the 3.5mm audio-style connectors that you see on some phones, MP3 players and development boards. TRRS st…
This is a SparkFun exclusive! These are 155mm long, 26 AWG jumper wires terminated as male to female. Use these to jumper fro…
This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE c…
These are various leaded cables for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. High q…
This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST co…
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing…
This is an inexpensive 3-foot-long HDMI to Mini HDMI cable that you can use to hook up your Raspberry Pi Zero W to a suitable…
This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST con…