Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
This 2x20 flat ribbon-cable fits the GPIO headers on the Raspberry Pi 3, 2, and B+ so you can easily connect to the low-level…
This is a basic SMA male to female connector cable at 25cm in length and RG174 housing.
This 0.012" Muscle Wire® (aka shape memory [Nitinol](http://en.wikipedia.org/wiki/Nickel_titanium)) is a one foot long piece…
This is a SparkFun exclusive! These are 12" long, 26 AWG jumper wires terminated as male to male. Use these to jumper from an…
When experimenting with GPS or RF it can be very handy to have the antenna on the top of your house or car with a clear view …
This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE c…
The is the official, 1m, micro HDMI to HDMI Cable for use with the Raspberry Pi.
This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE …
This 10m (33') SMA extension does a great job of connecting your receiver or radio to a distant antenna with as little RF los…
Standard 22 AWG solid Black hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes …
The Raspberry Pi Zero and Zero W are both equipped with a smaller CSI (Camera Serial Interface) port than on a full-sized Ras…
This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE c…
This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST con…
Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing…
This is an inexpensive 3-foot-long HDMI to Mini HDMI cable that you can use to hook up your Raspberry Pi Zero W to a suitable…
USB On-The-Go is a really useful USB specification! It allows some small devices that would usually be unable to act as a hos…
These 0.8m cables have minor, yet genius modifications that allow both ends to be plugged into their ports regardless of thei…
This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with th…
This panel mount USB-B (female) to micro-B (male) cable enables you to more easily enclose a project that contains a USB micr…
This is a USB to TTL Serial Cable which allows for a simple way to connect TTL interface devices to USB.
This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE …
Do you fear that your power may not be "far reaching" enough? How would another 3' work for you? Okay, so it doesn't sound ve…
This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin Molex co…
This 0.012" Flexinol® Actuator Wires (aka shape memory [Nitinol](http://en.wikipedia.org/wiki/Nickel_titanium)) is a one foo…
It can be difficult to get a wall-wart where you need it. The promise of PoE (power over ethernet) is great, but what if your…
This is a USB 2.0 type B to Mini-B 5-pin black cable. You know, the mini-B connector that usually comes with USB Hubs, Camera…
This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE…
Standard 22 AWG solid Red hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in…
Integrating Ethernet support into your project is a great way to relay data through a local area network and even bounce info…
This product is designed to connect the [RTK Surveyor](https://www.sparkfun.com/products/17369) product line to the popular […
A U.FL to SMA (jack) bulkhead straight connector with a 1.32 mm diameter cable.
The MyoWare® 2.0 Reference Cable is meant as an extension for the MyoWare 2.0 Muscle Sensor's reference pin.
Pi Zero Micro USB to USB A is a really useful USB specification! It allows some small devices that would normally be unable t…
12" long cables terminated with banana plugs, ideal for the micro:bit and gator:bit ecosystems.
SMA to MMCX Connector. Adapts MMCX jack to a standard SMA bulkhead. This cable interfaces to the GM862 Cellular modules and t…
This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opp…
USB-A to USB-C with real-time display charging power, all in a 4ft cable!
Standard 22 AWG stranded black wire. Use this for soldering wire or any project in which you need flexible wire. Stranded wir…
TRRS connectors are the 3.5mm audio-style connectors that you see on some phones, MP3 players and development boards. TRRS st…
These 4-pin JST-SM pigtail connectors mate perfectly with LED strips and other applications that require only two lines and a…
These 0.3m cables have minor, yet genius modifications that allow both ends to be plugged into their ports regardless of thei…
Standard 22 AWG solid White hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes …
This is a basic SMA male to female connector cable at 1M in length and RG174 housing.