The HUB-ee is a type of robot servo but designed for wheels, in fact it is a wheel, but it is also a motor, a sensor and a…

These nylon standoffs are 3/4" long and tapped for a 4-40 screw. These are great for mounting your board in an enclos…

 These 360° rotation 7:1 gear ratio channel gearbox kits incorporate threaded side mounts to easily attach a stand…

These precision gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost an…

This set includes a plastic plate with an 11x31 mm grid of 3 mm holes spaced 5 mm apart, which provides space fo…

These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost any…

These are resistant XL sized timing belts that fit snug inside of the Actobotics timing pulleys. Each belt is made out of …

The BOT120 PICAXE 20x2 Microbot is a simple to assemble kit that uses a unique design which requires no soldering of wires…

Pillow block bearing mounts attach to the outside of a channel and can be used as simple hinges. These bearing mounts have…

These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor sh…

 This powerful motor is the Hitec HS-625MG servo. This is one of the strongest metal gear servos that is available and…

These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost any…

 These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electrom…

These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost any…

Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floati…

Track set for tank treads. Use these treads to create your own tank setup. These work superbly with the Tamiya dual gear bo…

These precision gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost an…

ServoBlocks increase a servo’s load-bearing capabilities by helping to isolate the lateral load from the servo splin…

These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electromechan…

These side mount brackets can function as mounts for encaps for Actobotics channels. They have two untapped holes spaced 0…

 These aluminum attachment blocks make it possible to connect two flat panels at a 90° angle. These blocks come in…

These flat bearing mounts attach to the face of a channel or plate and have a  ball bearing with a 1/2” bore for…

These precision gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost an…

These flat bearing mounts attach to the face of a channel or plate and have a  ball bearing with a 1/4” bore for…

This custom-designed plastic wheel from Pololu has a rubber tire measuring 1.65" (42 mm) in diameter and is desi…

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 210:1 and operate up t…

The Pololu Pushbutton Power Switch from Pololu is a compact, solid-state power switch controlled by a momentary pushbutton …

 These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes…

 The Bluetooth Cubelet contains a tiny Bluetooth radio that you can pair with your Android device or PC. With the…

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to…

 These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electrom…

Metal long standoffs: 1" long x 1/4" OD. Used to get your proto board up off the table. #4-40 thread. Fits most d…

 These quad hub mounts can attach to the end or the middle of Actobotics channels to provide you a 90 degree angle wit…

The new version of the Ardubot PCB breaks out all the Arduino pins to a separate row of headers. It also includes spaces f…

 These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electrom…

These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor sh…

Metal short standoffs: 3/8" long x 1/4"OD. Used to get your proto board up off the table. #4-40 thread. Fits all …

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 5:1 and operate up to …

Quad block bearing mounts attach to the inside of a channel and have a ball bearing with a 1/4” bore for shafts. Thes…

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up t…

ServoBlocks increase a servo’s load-bearing capabilities by helping to isolate the lateral load from the servo splin…

 The Drive Cubelet contains a motor and roller wheels for moving on a horizontal surface and moves in one directi…

These shaft-mountable aluminum timing pulleys use XL timing belts and attach to a 6mm output shaft with a set screw. They h…

A metal caster used for omni-directional robots. Omni-what? Imagine a robot with the dual-motor gear box. The robot can…

The swivel hub lets you connect any two parts with the 0.77" hub pattern together and have them swivel a full 360 deg…

These set screw hubs make it capable to connect a micro gearmotor with a 3mm bore to a precision disk wheel or other objec…

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 30:1 and operate up to…

 These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes…

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 250:1 and operate up t…

The Pololu Pushbutton Power Switch is a compact, solid-state power switch controlled by a momentary pushbutton switch. Beca…