Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Mon-Fri, 9am to 12pm and 1pm to 5pm U.S. Mountain Time:
(303) 284-0979
Chat With Us
Jump to Subcategory:
added to your cart!
This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the…
These are a pair of right angle, hobby gearmotors from DAGU. These gearmotors are the same ones utilized in the Magician Chas…
The three-layer Circular Robotics Chassis Kit is a sturdy, miniature robotics kit designed for beginners and experienced robo…
The SparkFun Pi Servo HAT allows your Raspberry Pi to control up to 16 servo motors in a straightforward and uncomplicated ma…
If you're looking for a chassis base for your next robot, look no further than the Rover 5. The Rover 5 uses 4 independent mo…
These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost anythi…
This is a simple ~140RPM (no load), DC planetary gearmotor.
Does controlling door access with the power of Electromagnetism interest you? Great! In effect, this latch / lock solenoid is…
This is the tinyESC v2 from [FingerTech Robotics](http://www.fingertechrobotics.com/), an ultra small bi-directional brushed …
This is a 6 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed throug…
These servo gears are made specifically to fit a Hitec C1 servo spline, allowing you to mate other gears to your servo. They …
ServoBlocks increase a servo’s load-bearing capabilities by helping to isolate the lateral load from the servo spline and c…
This is the versatile Hitec HS-425BB servo. This little guy is able to take in 6 volts and deliver 57 oz-in. of maximum torqu…
Ready to add some good vibes to your project? Look no further than the SparkFun Haptic Motor Driver. This board breaks out Te…
These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along th…
The GoPiGo Beginner Starter Kit from Dexter Industries is a complete robotics kit controlled by the Raspberry Pi 3 B+.
The Pololu 15 Amp high-power motor driver is a discrete MOSFET H-bridge designed to drive one DC brushed motor. The H-bridge …
This dual bidirectional motor driver, from [Cana Kit](http://www.canakit.com/), is based on the very popular [L298](http://ww…
The Tenergy 5-in-1 Intelligent Cell Meter takes you one step closer to becoming an all-seeing and all-powerful battery wizard…
This is easily the most rugged and beefy robot chassis in its price range. The Wild Thumper 6-Wheel platform is the best of b…
This beast is the Hitec HS-805BB servo. Able to take in 6 volts and deliver an impressive 343 oz-in. of maximum torque at 0.1…
The EggBot is back and it's been improved! The classic open-source art robot that captured our hearts (by drawing on spherica…
The SparkFun Serial Controlled Motor Driver (SCMD) is a DC motor driver that’s been designed to drive small DC motors with …
The Pixhawk Radio Telemetry Kit is a lightweight and inexpensive open source radio platform that can allow for ranges of 300m…
The SparkFun Wireless Motor Driver Shield is designed to make connecting motors, sensors and other components to your Arduino…
Do you have some liquids that you need to move? This fluid pump will move 350 gallons per hour! The SEAFLO mini water pump ha…
This is the Multi-Chassis Basic 4WD Kit, an easy to assemble and use robot chassis platform. The Multi-Chassis kit provides y…
These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 150:1 and operate up to 1…
This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed throu…
The SparkFun RedBot Mainboard is a robotic development platform that works with the Arduino IDE. The RedBot is a motor driver…
This powerhouse is the Hitec HS-755HB servo. Able to take in 6 volts and deliver an impressive 183 oz-in. of maximum torque a…
The two-layer Circular Robotics Chassis Kit is a sturdy, miniature robotics kit designed for beginners and experienced roboti…
A metal caster used for omni-directional robots. Omni-what? Imagine a robot with the dual-motor gear box. The robot can piv…
The universal aluminum mounting hub allows you to mount custom wheels and mechanisms to 5 mm motor shafts. The hubs are sold …
This is the Hobby Motor and Encoder Kit from DAGU, an inexpensive and reliable set of add-ons for your next robotic project. …
This 0.012" Muscle Wire® (aka shape memory [Nitinol](http://en.wikipedia.org/wiki/Nickel_titanium)) is a one foot long piece…
This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism usin…
You better call Dr. Grant because we've got a T'Rex! If you thought our previous robot chassis were beefy and rugged then you…
With this Channel Slider kit from [Actobotics](https://www.sparkfun.com/pages/Actobotics) you will be able to put your videos…
The SparkFun Continuous Rotation (CR) Servo Trigger is a small robotics board that simplifies the control of hobby RC servo m…
The MOTORplate from Pi-Plates brings a suite of professional motion control features to your Raspberry Pi. These plates can e…
These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 50:1 and operate up to 12…
These pinion gears attach to a ¼” D-shaft or gear motor using a setscrew. They have 16 teeth with a gear pitch of 32P, an …
Pillow block bearing mounts attach to the outside of a channel and can be used as simple hinges. These bearing mounts have a …
No, this isn't a tank tread, this is a 0.5m long Cable Carrier with 10x15mm bits composing its main body and two screw fasten…
Forgot your password? No account? Register one!
