Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
added to your cart!
This hardware kit consists of four each of M2 style nylon hex nuts and screws.
With the Gas Sensor Breakout you will be able to utilize each oversized, oddly spaced pins featured on every MQ gas sensor pr…
6 pin SOT-23 to DIP adaptor. Created to take SOT23 of various pin sizes breakout to DIP. This will work with 3-pin MOSFETs, B…
The SparkFun Qwiic SHIM for Raspberry Pi is a small, easily removable breakout that easily adds a Qwiic connector to your Ras…
RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a…
A kit that includes all the male headers needed for your Raspberry Pi Pico board.
This is a right angle 5mm addressable LED. It sounds boring, but at the time of writing, *this is the first one in the world*…
This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. **Note:** Po…
A simple breakout PCB for the GP1A57HR photo interrupter (also known as a photogate, photodiode, or phototransistor). This PC…
The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic enabled board.
The SparkFun ESLOV to Qwiic Bridge lets you quickly and easily connect Qwiic breakouts to Arduino boards with an ESLOV connec…
This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. T…
Sure, your flashing, chip-tune playing T-shirt is really cool at the party... but at some point you need to turn it off. And …
Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to t…
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire [Wheatstone bridg…
We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and open…
This is the breakout board for the [thumb joystick](http://www.sparkfun.com/commerce/product_info.php?products_id=9032). Pins…
This is a simple breakout board for our RFID readers. The SparkFun RFID Reader Breakout converts the 2mm pins to bread board …
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can e…
The Qwiic MultiPort adds additional ports to boards that have only one Qwiic port on the I2C bus.
The SparkFun Rotary Switch Potentiometer Breakout is a small board the allows you to add resistors to a [10-position rotary s…
This parts kit allows you to modify a coolant hose into an additional hand for your SparkFun Third Hand. It includes the alli…
This is the 36mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards side by side. This FPC has an …
This is the 100mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards end to end. *** _**smô…
This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but i…
These paper-thin, adhesive EPCglobal Gen2 tags work with our RFID readers and can be stuck to practically anything.
The SparkFun Multiplexer Breakout provides access to all pins and features of the 74HC4051, an 8-channel analog multiplexer/d…
This simple board breaks out a micro-B USB connector's VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to ad…
This is a breakout board for the [L298N](http://www.sparkfun.com/commerce/product_info.php?products_id=9479) full-bridge dual…
The SparkFun 8-Pin SOIC to DIP Adapter is a small PCB that lets you adapt SOIC packages into a DIP footprint. These tiny boar…
This is a simple pack of five Pink LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at yo…
This version of the QRE1113 breakout board features an easy-to-use analog output, which will vary depending on the amount of …
This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at …
The Line Follower sensor is an add-on for your RedBot that gives your robot the ability to detect lines or nearby objects. Th…
The SparkFun 16-Pin SSOP to DIP Adapter is a small PCB that lets you adapt SSOP packages into a DIP footprint. These small bo…
The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.…
This version of the QRE1113 breakout board features a digital output, using a capacitor discharge circuit to measure the amou…
The SparkFun Qwiic Button Breakout simplifies all of those nasty worries away into an easy to use I2C device, and with our Qw…
This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all o…
This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the …
8-Pin SSOP to DIP break out board. The footprint was rotated to accommodate different width SSOP devices and can be used with…
This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at y…
This is a simple pack of five Blue LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at yo…
This is a simple pack of five Green LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at y…
This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at you…
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1011 S…
Qwiic Boost increases the Qwiic bus from 3.3V to 5V while still providing the target device with 3.3V I2C signals. This is a …
If you need to add user input without using a button, then a capacitive touch interface might be the answer. The AT42QT1010 S…
The Soft Power Switch is a passive, hard on/off switch with software feedback and control. In other words, it's like the on/o…
This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs …